How to Install Your Solid Timber Mantel (DIY Guide)

Renaissance Wood & Timber builds and supplies solid timber fireplace mantels from our Oklahoma City shop. We do not install them. This guide is for homeowners or their contractor, and it covers the two mounting methods we use.

Use Method 1 if your mantel is drilled to fit a steel floating-mantel bracket. Use Method 2 if your mantel has a pocket carved into the back.

A note before you start

Confirm that your wall structure and fasteners are suitable for the mantel’s weight. Follow fireplace clearance requirements and local building codes. If you are unsure, consult a qualified contractor. This guide does not replace professional judgment about your wall or fireplace.

Method 1: Mounting Bracket

For mantels drilled to fit a steel floating-mantel bracket.

What you’ll need

  • Mantel mounting bracket
  • Lag screws
  • Drill / driver
  • Socket or driver bit
  • Level
  • Stud finder
  • Pencil
  1. Step 1 of the mounting bracket method: use a stud finder to mark every stud and draw a light level line where the bracket will sit.

    Find the studs

    Use a stud finder to mark every stud. Draw a light level line where the bracket will sit.

  2. Step 2 of the mounting bracket method: hold the bracket on the line and level it so the screw holes around its edge line up with the studs.

    Level the bracket

    Hold the bracket on your line and level it. The screw holes around its edge let you line up with every stud.

  3. Step 3 of the mounting bracket method: drive lag screws through the edge holes into every stud the bracket crosses.

    Screw it to the studs

    Drive lag screws through the edge holes into every stud the bracket crosses. More studs = more strength.

  4. Step 4 of the mounting bracket method: slide the mantel's pre-drilled holes onto the rods and push it snug against the wall.

    Slide on the mantel

    Slide the mantel’s pre-drilled holes onto the rods and push it snug against the wall.

Good to know

  • Hit as many studs as you can. Every stud you screw into makes the mantel stronger.
  • The bracket mounts right over your drywall. There’s no need to cut it out.
  • Want it permanent? Put construction adhesive on the rods before you slide the mantel on.
  • Brick or stone wall? Use masonry anchors made for it instead of lag screws.

Method 2: Mounting Recess (Pocket)

For mantels with a pocket carved into the back.

What you’ll need

  • One 8 ft 2x4
  • Lag bolts or structural screws
  • 6–8 deck screws
  • Saw
  • Drill
  • Level
  • Stud finder
  1. Step 1 of the mounting recess method: the back of the mantel has a pocket carved by Renaissance that slides over a wood ledger.

    The pocket

    Your mantel comes with a pocket carved into the back. It slides over a simple wood ledger.

  2. Step 2 of the mounting recess method: cut an 8 foot 2x4 in half to make two 4 foot pieces.

    Cut one 2x4

    Cut an 8 ft 2x4 in half to make two 4 ft pieces.

  3. Step 3 of the mounting recess method: stack the two 2x4 pieces face to face to make a ledger 3 inches by 3 and a half inches by 4 feet.

    Stack the pieces

    Stack the two pieces face to face (wide sides together). That’s your ledger: 3" × 3½" × 4 ft.

  4. Step 4 of the mounting recess method: hold the ledger level and bolt it into every stud it crosses.

    Bolt it to the wall

    Hold the ledger level where the mantel will hang. Bolt it into the studs.

  5. Step 5 of the mounting recess method: slide the mantel's pocket over the ledger until it is tight to the wall.

    Slide on the mantel

    Slide the mantel’s pocket over the ledger until it’s tight to the wall.

  6. Step 6 of the mounting recess method: drive 3 to 4 deck screws through the top of the mantel into the ledger, 1 inch from the wall, and sink the heads.

    Screw down from the top

    Drive 3–4 deck screws through the top into the ledger, 1" from the wall. Sink the heads.

  7. Step 7 of the mounting recess method: drive 3 to 4 more deck screws up through the bottom, 1 inch from the wall, and sink the heads.

    Repeat from the bottom

    Drive 3–4 more deck screws up through the bottom, 1" from the wall. Sink the heads.

Cross-section

Cross-section of a finished mounting recess install: the two-by-four ledger fills the pocket, with lag bolts into the stud and deck screws top and bottom 1 inch from the wall.

Finished install: the ledger fills the pocket, with screws top and bottom 1" from the wall.

Browse mantels or visit the showroom

When you’re ready to choose a mantel, browse our solid timber mantels, or contact us / book a showroom consultation at our Oklahoma City shop.

Browse Solid Timber Mantels Contact Us Showroom Consultation